1、路由实例

企业建站必须是能够以充分展现企业形象为主要目的，是企业文化与产品对外扩展宣传的重要窗口，一个合格的网站不仅仅能为公司带来巨大的互联网上的收集和信息发布平台，创新互联面向各种领域：建筑动画等网站设计、成都全网营销解决方案、网站设计等建站排名服务。

路由实例是路由表、接口和路由协议参数的集合。通过设置接口及路由协议各种参数可以形成路由实例的路由表。

每个路由实例都有自己的实例名称，并且各自维护一张独立的路由表。

全局路由其实也是一个路由实例，其实例名称为inet.0。

2、普通静态策略路由（只做策略，不作NAT转换）

设置包括如下步骤：

1）设置应用接口子接口，定义为服务区域的入接口/出接口

2）定义路由实例，实例类型为forwarding，实例路由表

3）定义过滤器firewall filter

4）定义接口路由组rib-group；

5）将接口路由组导入到全局路由表及路由实例的路由表中；

6）在内网接口应用过滤器filter

3、做NAT的静态策略路由（既做策略又做NAT转换）

注意：

1）该情况下需要试用virtual-router类型的路由实例

2）每个virtual-router维护一张独立的路由表

配置实例拓扑图

达到目的：

默认内网主机上网走CNC 2M链路访问公网，指定的PC走CNC 50M链路访问外网

实现思路：

默认内网所有主机通过全局路由表inet.0走CNC 2M链路出局访问公网，部分指定的PC通过Juniper SRX的FBF路由策略走路由实例的路由表出局访问公网

设置步骤如下：

1）定义服务区域zone

配置示例：

set security zones security-zone lt host-inbound-traffic system-services all

set security zones security-zone lt host-inbound-traffic protocols all

2）设置应用接口子接口，定义为服务区域的入接口/出接口

配置示例：

set security zones security-zone lt interfaces ge-0/0/2.0 host-inbound-traffic system-services all

set security zones security-zone lt interfaces ge-0/0/2.0 host-inbound-traffic protocols all

3）定义路由实例，路由实例数量可根据接入的ISP线路数量来定义。实例类型为virtual-router，VR的虚拟接口，VR的路由表

配置示例：

set routing-instances CNC50M instance-type virtual-router

set routing-instances CNC50M interface ge-0/0/2.0

set routing-instances CNC50M routing-options static route 0.0.0.0/0 next-hop XX.XX.XX.XX  ##指向ISP提供的公网网关

4）定义NAT的相关映射rule-set、rule，策略policy、address-book、application等

√Source NAT的rule-set 配置示例：

set security nat source rule-set CNC50M-snat-internet from zone trust

set security nat source rule-set CNC50M-snat-internet to zone lt

set security nat source rule-set CNC50M-snat-internet rule CNC50M-inside-to-outside match source-address 0.0.0.0/0

set security nat source rule-set CNC50M-snat-internet rule CNC50M-inside-to-outside match destination-address 0.0.0.0/0

set security nat source rule-set CNC50M-snat-internet rule CNC50M-inside-to-outside then source-nat interface

√ 策略policy 配置示例：

set security policies from-zone trust to-zone lt policy CNC50M-snat-internet match source-address CBGZ-out-norestrict

set security policies from-zone trust to-zone lt policy CNC50M-snat-internet match destination-address any

set security policies from-zone trust to-zone lt policy CNC50M-snat-internet match application any

set security policies from-zone trust to-zone lt policy CNC50M-snat-internet then permit

set security policies from-zone trust to-zone lt policy CNC50M-snat-internet then log session-init

set security policies from-zone trust to-zone lt policy CNC50M-snat-internet then log session-close

5）定义过滤器filter

配置示例：

set firewall family inet filter filter-1 term LAN_term from destination-address 172.16.0.0/16

set firewall family inet filter filter-1 term LAN_term from destination-address 172.20.0.0/16

set firewall family inet filter filter-1 term LAN_term from destination-address 192.168.0.0/16

set firewall family inet filter filter-1 term LAN_term then accept     ##允许内网PC互访，不作以上配置将会导致网关为此防火墙内网接口的PC无法访问内网其他PC。

##指定的PC从CNC 50M链路出局访问公网

set firewall family inet filter filter-1 term CNC50M_term from source-address 172.16.29.25/32

set firewall family inet filter filter-1 term CNC50M_term from source-address 172.16.29.251/32

set firewall family inet filter filter-1 term CNC50M_term from source-address 172.16.28.166/32

set firewall family inet filter filter-1 term CNC50M_term from source-address 172.16.28.137/32

set firewall family inet filter filter-1 term CNC50M_term from source-address 172.16.28.139/32

set firewall family inet filter filter-1 term CNC50M_term from source-address 172.16.28.138/32

set firewall family inet filter filter-1 term CNC50M_term then routing-instance CNC50M

set firewall family inet filter filter-1 term default then accept ##对于filter的其他数据，采取默认动作accept（接受）

6）定义接口路由组

配置示例：

set routing-options interface-routes rib-group inet INSIDE

7）将接口路由组导入到全局路由表及实例的路由表中

配置示例：

set routing-options rib-groups INSIDE import-rib inet.0

set routing-options rib-groups INSIDE import-rib CNC50M.inet.0

set routing-options rib-groups INSIDE import-rib default.inet.0

8）在内网接口应用相应的过滤器filter

set interfaces ge-0/0/0 unit 0 family inet filter input filter-1

4、普通静态策略路由与NAT转换的策略路由之间的区别

路由实例类型不同：

普通静态策略路由类型：forwarding

NAT转换的策略路由类型：virtual-router

参考链接：http://www.docin.com/p-598358767.html

当前名称：JuniperSRX策略路由总结
本文来源：http://csdahua.cn/article/jdsihp.html